Quantcast
Channel: PowerEdge General HW Forum - Recent Threads
Browsing all 5911 articles
Browse latest View live

PowerEdge 1750: setting up the raid

My plan for this Poweredge 1750 is not so much for use as a server as for capturing an uncompressed video stream. I will need to obtain something around 35Mbit/sec write speed to the internal SCSI...

View Article


Re: PowerEdge 1750: setting up the raid

Hello scooter250scooter250I will need to obtain something around 35Mbit/sec write speed to the internal SCSI drives.Is this doable using what comes with the factory machine or am I asking too much?That...

View Article


Re: PowerEdge 1750: setting up the raid

ooops!  Got my bits and bytes messed up again.The correct answer is: I need a sustained data rate of at least 30 to 35 MB/second.How do I stand now?

View Article

Incorrect time on Server

I've got a power edge 710 that continually shows the wrong time.  Server 2003r2 enterprise.  I've tried the following:Re registering windows time service.Using domhier settings in registry to sync with...

View Article

Re: Incorrect time on Server

Is the time correct in the BIOS screen?

View Article


Re: PowerEdge 1750: setting up the raid

scooter250I need a sustained data rate of at least 30 to 35 MB/second.How do I stand now?That will be questionable. Some 10K RPM drives may have difficulty sustaining that write speed. What is the...

View Article

Re: Incorrect time on Server

I replaced the battery last night, and it said "system clock not set" which i figured was OK after replacing the battery.  Once booted, the windows event viewer logged the server getting a correct time...

View Article

Re: Incorrect time on Server

if you didnt set the time in the BIOS, thats your issue, set it there first please.

View Article


Re: Incorrect time on Server

I'll give it a shot.

View Article


Image may be NSFW.
Clik here to view.

R410 BIOS Update fails with "doDepcheck Failed" error

R410Server 2012BIOS_VHP27_WIN32_1.11.0.exe - for the BIOS update.Disabled idrac virtual media detached, turned it off entirely.Not finding much online about this besides detaching idrac detach, any ideas?

View Article

Re: R410 BIOS Update fails with "doDepcheck Failed" error

Hello jellyglovesIt is a dependency check within OpenManage. I would suggest uninstalling OMSA and installing the latest version. If that does not resolve the issue then you can disable the check by...

View Article

Re: PowerEdge 2900 - Windows Server 2003 R2

In my opinion, you are looking at a corrupt RAID array rather than a bad controller (your good/remaining disk has an unreadable block(s) that it cannot replicate to the rebuilding drive).  Of course,...

View Article

Re: Hyper-V & Precision 490

Installing 2008R2/2012 you will likely run into the same thing since Hyper-V is based on the same kernels as the Servers.Changing SATA Operation to ATA or Combination should disable AHCI, making it so...

View Article


Re: Disabling on board video on Dell 500SC

My video card died on me. How can I install a new card ( a Radeon 7000) on my 500SC?

View Article

Re: Disabling on board video on Dell 500SC

Moved your post to a new thread since the original thread was over 10 years old.Adding graphics to a server is a matter of trial and error (unless you can use ones that others have verified to work)...

View Article


Re: Hyper-V & Precision 490

Hey Flash, well is this funny ... I checked and its running A08 for the bios so its up to date .. I got a copy of Server 2012 from MS and installed with it no trouble at all .. works great .. Running...

View Article

Re: R710 2nd CPU Install - E1410

Okay. I did try one more thing. I took out the processor in Socket 1 and only left the one in Socket 2 in place. It was actually able to post however after post it came up with an "Error: CPU1 Not...

View Article


Re: PowerEdge 1750: setting up the raid

I have not purchased anything as yet. Still trying to figure out what will work. I'm leaning now to something like the 2850. It offers more HD's, embedded graphics and three PCI slots.I will take all...

View Article

Re: R710 2nd CPU Install - E1410

The stepping code has traditionally been printed on the processor itself, however, looking at Intel's website for the E5540, it appears as if D0 is the only stepping available for that processor.  This...

View Article

"The watchdog timer expired" - m710HD

Hi,What does this message in the drac logs mean?Thx,John Bradshaw

View Article
Browsing all 5911 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>