Re: SAS 6/IR integrated
why does the PERC 6 not show up under my system as being compatible? can you please provide a link?
View ArticleClik here to view.
Re: SAS 6/IR integrated
Where are you seeing (or not seeing) it as incompatible?content.dell.com/.../dell-raid-controllers.aspx
View ArticlePoweredge 840- Amber light Flashing
I bought a refurbished/used Dell Poweredge 840 from a reseller over the internet. Since buying it i have installed a raid card, added 4 hard drives, installed server 2008 standard, and have used the...
View ArticleRe: Poweredge 480- Amber light Flashing
What RAID controller did you get?Try booting into CTRL-E to see if you can access the ESM/SEL logs.I would recommend trying to boot to an OMSA Live CD to check the Hardware...
View ArticleRe: Poweredge 480- Amber light Flashing
The RAID controller is :Adaptec AAR-2610SA Dell 0H2052 64MB Serial SATA RAID Controller Card 6 PortsI have one of these working just fine on another server. Was able to go into the raid utility and do...
View ArticleRe: Poweredge 480- Amber light Flashing
Another important thing is that I just plugged in the server and it initially shows blue light all the way up to the point where the os cd is trying to load the install gui. then it gives the bsod...
View ArticlePowerEdge 6950 Memory Config
Good Evening - Maybe someone has seen this problem I am having with the listed server - PE 6950 I am trying the get the system to read 32GB of ram, <server running four processors> the config I...
View ArticleRe: Poweredge 480- Amber light Flashing
voices.yahoo.com/dell-xps-amber-light-problem-solution-4124627.htmlI read through this link and found something important. It turns out the memory modules were needed to be reset.That's all I did....
View ArticleRe: PowerEdge 6950 Memory Config
Hello GerryI'm surprised that the operating system is detecting 24GB of memory. 1 DIMM in each bank is not a valid configuration. The DIMMs are supposed to be installed in pairs, so a minimal...
View ArticleRe: Which Motherboard do I have? Poweredge 2800 server.
Thank you for clearing that up. I am very new to servers in general. I just received this PE2800 for free. It was bare, No RAM, No HDDs, only one processor. Before this I was using an old desktop with...
View ArticleRe: Which Motherboard do I have? Poweredge 2800 server.
Sound like fun :) (and the best way to get into it).Take care.
View ArticleRe: Poweredge 480- Amber light Flashing
There are dozens of things that can cause the amber light and cause the system to behave strangely (including amber lights at various stages of POST). Memory errors are just one ... you got extremely...
View ArticlePowerEdge R610 citrix xenserver installation on SD card (16,32 or 64GB)
Hi all!We have 4 PowerEdge R610 servers with iDrac6 enterprise card. And we wanna install citrix xenserver hypervisor on SD card instead of local HDD or SAN disks. I tried use back port of iDrac6...
View ArticleRe: PowerEdge 2900 - Windows Server 2003 R2
It's Windows Server 2003 R2 32bit SP2. Driver and firmware version: lsi_sas.sys (1.28.03.01 built by: WinDDK, 94.50 KB (96,768 bytes), 28/05/2009 17:33) We haven't cleared the ESM log. Hasn't been...
View ArticleRe: PowerEdge 2900 - Windows Server 2003 R2
Forgot to include the firmware version:- 00.25.47.00.06.22.03.00
View ArticleRe: PowerEdge R610 citrix xenserver installation on SD card (16,32 or 64GB)
If you have the installation CD\DVD, you should be able to install XenServer to the SD card. When the installation starts, point the install to the SD rather than the hard drive and complete the...
View ArticleRe: PowerEdge R610 citrix xenserver installation on SD card (16,32 or 64GB)
Hello,We have installation CD\DVD, but I do not able select SD card for install. I can select SD card as boot Disk in BIOS, But can not see it in iDRAC6 or point the install to the SD card.I tried some...
View ArticleDell UPS Rack/Tower 2700W and a R710 ESX 4.0 / ESXi 4.1 environment
Hello,Been struggling with this for a while with reseller, but their answer is, "not possible".Which I don't want to accept...We have several sites with:Dell UPS Rack/Tower 2700WDell R710 with ESX4 /...
View ArticleRe: PowerEdge 2900 - Windows Server 2003 R2
I've cleared the EMS logs and the Hard Drive is now syncing up - will see how it goes and report back. It normally gets to about 30% then crashes. So I'll leave it running over night and report back.
View ArticleRe: Dell UPS Rack/Tower 2700W and a R710 ESX 4.0 / ESXi 4.1 environment
The last power state is OFF, so the server will not power back up. The server is set to shutdown after the VM's are gracefully shutdown. Regards,
View Article