Re: trouble initializing blades on m1000e
Charles, Can you check below items and let me know the same1: Can you check Hardware log after inserting the blade and check whether any message related to the inserted blade. If CMC log...
View ArticleRe: PowerEdge C1100 dead in the water...
Ipaqted, If you have an onhand copy of that ROM, can you email it to me? I will post on our FTP site for others that have bricked their systems, and don't have a backup....Thanks
View ArticleRe: trouble initializing blades on m1000e
Shine,1. the Hardware log show that the blade is inserted2. CMC FW version = 4.31 (updated this morning); iDRAC FW version = 3.20 (build 42) - this is a good blade (M610) that used to work3. LCD panel...
View ArticleHow many arrays does the Perc 6i on a Dell T610 running ESXi 5.0 support and...
Running 1 ESXi 5.0 U2 host with 3 vms. (2 Server 2008 R2 and 1 Server 2003 R2) with 32 GB RAM.Our business is looking on purchasing a new software that will requiere an additional 3 virtual servers.My...
View ArticleRe: How many arrays does the Perc 6i on a Dell T610 running ESXi 5.0 support...
SDLC,Yes you can create a new array without causing any issues with the primary array. The Perc 6/i can support multiple arrays, up to 64 to be precise. You may also use different specs on the drives...
View ArticleRe: How many arrays does the Perc 6i on a Dell T610 running ESXi 5.0 support...
Chris,thanks for the quick response. I am then going to create a new array with the 4 drives I am going to purchase. Can I also mix SAS and SATA drives or would they need to be all SAS drives?I might...
View ArticleDell 2950 FlexRAID
Hello everyone,Had a chance to purchase a 2950. I would like the ability to use FlexRAID and have a few questions regarding the modifications needed to allow this. As I understand, I will not be able...
View ArticleRe: PowerEdge C1100 dead in the water...
Hi,I may or may not have 1.Post your FTP site, maybe someone has 1 already.Good Luck.
View ArticleRe: Dell PowerEdge T620 performs power characterization at each boot
Hi adesIT Since you said you can disable the In-System Characterization, have you tried that? Does that resolve the issue?Let us know please.
View ArticleRe: Dell PowerEdge T620 performs power characterization at each boot
Hello Manfred,Thanks for your reply. Yes I tried to disable the In-System Characterization and it works fine now. I guess as long as I don't add or remove any hardware it should be OK to leave it like...
View ArticleRe: E122C lcd message on poweredge 2950
Dear Flash1932,Thanks alot for info. i have been facing another problem now. its redundant server is restarting again & again on the error of e1229 cpu 1 vcore. is this cpu 1 is the master cpu...
View ArticleRe: Dell PowerEdge T620 performs power characterization at each boot
Hi adesITIt seems this error is related to the bios."ICS is a 12G BIOS feature that optimizes the ratio of power and performance of a system. When set to enabled in the BIOS, ICS will normally run when...
View ArticleClik here to view.
Re: How many arrays does the Perc 6i on a Dell T610 running ESXi 5.0 support...
You can't mix them in the same array, but the controller can support sas and sata arrays at the same time. No, you wouldn't be able to install OMSA on the VM, as it would only see what you have the VM...
View ArticleRe: E122C lcd message on poweredge 2950
CPU's are normally numbered 1 and 2 on the server, rather than 0 and 1.If it does this with both processors in slot 1 (in a single processor configuration), then I would plan to replace the motherboard...
View ArticleMounting a Dell R310 in a RACK of 60x60x60 cm
Hi all!Is possible with this rail kit : 770-10940 to mount an R310 in a 60x060x60 Rack ?someone knows what is hte minimal lenght of the rail?thanks
View ArticleRe: Mounting a Dell R310 in a RACK of 60x60x60 cm
Hello geniusmikiI can't speak to those rails specifically because I don't know what they are. They don't look like the rails for this server, and that is not a Dell part number I am familiar with. Here...
View ArticleRe: Dell C1100 / CS24-TY bios and ems/ibmc update
I'd love to know the answer to this too...I am not having any issues except I'm not content with how my Revodrive is being seen. I'm intending on using my CS24 as a napp-it box.
View ArticleRe: Dell C1100 / CS24-TY bios and ems/ibmc update
He just did the ones from the site. I can link them for you if you need me to, but you'll see them right there on the pages.
View ArticleRe: trouble initializing blades on m1000e
I've tried everything I know to do. Does anyone have any ideas?Thank you for your help.Charles
View ArticleRe: Interpreting Diagnostic Messages
Take the server down to the minimum to POST: The minimum components to allow the PowerEdge™ 1900 to complete POST are: System board Processor (with heatsink) in socket 1 One stick of memory in slot 1 1...
View Article