Re: Plex Media Server on 32bit Ubuntu on ESX 3.5 on 2800.
So if you crop this down a bit it's clear there is a notable difference in the memory access profiles of the two run types and this is most likely a consequence of the transcoder's media-specific...
View ArticleRe: Power Edge T310 Memory Support
The R710 support limits UDIMM's to 2 per channel as well. Each side of the R710 has 3 channels. It will support up to 24gb of UDIMM's with memory on both sides with 2 processors. Regards,
View ArticleRe: Power Edge T310 Memory Support
Just to clarify, the T310 has two channels, 3 slots per channel, and is single processor.The R710 has three channels, three slots per channel, per processor. Making 1 2GB UDIMM per channel, per...
View ArticleRe: Power Edge T310 Memory Support
Any chance since the Technical Guide publishing, that the T310 supports UDIMM larger than 4GB or RDIMM larger than 8GB?
View ArticleRe: Power Edge T310 Memory Support
The largest supported UDIMM on the T310 is 4gb. Here is the part number and specifications: R1P74 4GB, UDIMM 1333 (Dual Rank) DIMM,4G,1333,2RX8,8,240,UBE,LV The largest supported RDIMM on the R710 is...
View ArticleRe: PowerVault NF500 upgrade options
Thank you again, Flash. You've been most helpful. I really do appreciate your willingness to share your knowledge and experience with someone like me who is obviously a noob.I'm going to give my boss 4...
View ArticleSolution to E1225 ESB 1.5V on a power edge 2950 gen2
Good afternoon everyone, i got this server last year is dell power edge 2950, everything has been running great in till this morningi got this error msg on the led E1225 ESB 1.5V.I tryed clearing the...
View ArticleRe: Solution to E1225 ESB 1.5V on a power edge 2950 gen2
Rdanetti,Would you power off the server and then reseat the riser and the processors? After that then clear the NVRam, you do this with a jumper that is located between the PCI slot and the dimm...
View ArticleRe: Solution to E1225 ESB 1.5V on a power edge 2950 gen2
Thanks for answering, i did everything and im still getting the same error. should i just replace the mobo?
View ArticleRe: Solution to E1225 ESB 1.5V on a power edge 2950 gen2
It sounds like it may be the cause of the issue. I'm going to send you an email requesting your svc tag. Please reply with the information and I can see what I can do for you.
View ArticlePowerEdge 1855 GbE Passthrough
Hello everyone. I am new to the whole blade server system, and I have a question about the 1855 GbE passthrough cards. How do they work? I incorrectly assumed that I could just plug in to port 1 on...
View ArticleRe: PowerEdge 1855 GbE Passthrough
Sean,Just to clarify. The PHY module will not link if connected to a 10MB or 100 MB infrastructure as the PHY module only supports gigabit speed. Also, the layout of the ports on the module are 9 - 7...
View ArticleRe: PowerEdge 1855 GbE Passthrough
That must be it, was connected to a 10/100 PowerConnect. Will try again with a GB switch, thanks!
View ArticleRe: PowerEdge 1855 GbE Passthrough
If I could get 4 of the 5316M modules, could I connect those into a 10/100 switch? Those function like normal switches, correct?
View ArticleRe: PowerEdge 1855 GbE Passthrough
The switches would slot into bays 1&2, only put switches into bays3&4 if you have the GBe mezzcard installed in the blades.I'm not sure if you can get these new from Dell but here's a link:...
View ArticleRe: PE2950 BIOS upgrade without floppy drive
Hi Rey,I do have a Dell Laptop & its the E series. But unfortunately this laptop does not belong to me. i wasn't able to get Windows 2008 to install from my USB but i did manage to get Xenserver...
View ArticleRe: PowerVault NF500 upgrade options
Flash,One more question. I'm not having any luck finding a 3rd party vendor of Dell certified drives. Can you tell me what I should be looking for?
View ArticleDell Poweredge R210 II not liking Tripplite Ps2 to USB adapter for KVM
system specswindows server 2008 R2 standard with pack 1intel xeon cpu 3.10ghz8g ram64bit osnamed Chaos for good reasonsthis server controls our HVAC system for 3 buildings. its all usb which was...
View ArticleRe: PowerEdge 1855 GbE Passthrough
I was able to find a deal on 4 of the 5316M modules yesterday so I went ahead and got them. Should I only use them in slot 1 and 2, or can I use them in all 4? What about using them in conjunction with...
View Article