Re: power option on R420
So are you basically saying that going with the 550W is the safe choice for now and in the future?
View ArticleRe: power option on R420
Yes. A $50-100 upgrade now can save you from a $300-400 upgrade later.
View ArticleRe: Dropped network connections between PowerEdge T610 running Windows Server...
Did you send a message to Kaspersky, I bet they would like to know this too :)
View ArticleHow to get blade Names to show on m100e
Hi,We cannot seem to get the trick right to get Blade Names, which are populated in the Server Overview/Setup/Slot Names, to show correctly on the front page of the M1000e (LHS of the Chassis page).We...
View ArticleRe: How to check last driver/firmware update
Here's another query around this. The read me file has supported operating system section (see below);Microsoft Windows Operating Systems* Microsoft(R) Windows Server(R) 2003 R2 Web, Standard and...
View ArticleRe: How to get blade Names to show on m100e
Hello JohnI suspect that this is an OMSA issue. Is OMSA installed on all of the servers? Do the servers that are not reporting host names correctly have anything in common, like the same OS or an OS...
View ArticleRe: How to check last driver/firmware update
I noticed that SUU 6.3 clearly indicates the OS which is 2003 Enterprise SP2 x86No R2 confusion in supported OS check list
View ArticleInternal USB on M420 or M620 blades
Does anyone have specs on the internal USB support for M420 or M620 blades?I know the manual reads, "CAUTION: To avoid interference with other components in the blade, the maximum allowable dimensions...
View ArticleRe: How to check last driver/firmware update
your statement is correct, its R2 web, R2 standard & R2 Enterprise Editions (all)with SP2 (32-bit x86)
View ArticleRe: Internal USB on M420 or M620 blades
The M420 only has 2 external USB ports and is not recommended to run an OS from a USB externally. The M620 does have an internal USB slot. However, Dell does not support running an OS from a USB key....
View ArticleRe: PowerEdge 2800 bios stop - F1/F2 message
My OpenManage Install is perfectly happy except that it's whining about wanting new drivers and firmware. Seeing that this server has been running just fine with what it's got for more than 8 years,...
View ArticleRe: PowerEdge 2800 bios stop - F1/F2 message
"Does anyone know how to suppress this message or skip the boot sequence interrupt?"Uninstall OMSA or ignore the message. What "boot sequence interrupt" are you talking about?Firmware and driver...
View ArticlePE2950 G3 problem with Perc 6i battery after firmware upgrade
Hi, I have 2 PE 2950 III with Perc 6i card. After upgrading my Perc 6i firmware to version 6.3.1-0003, I have 1 server that report an error. After investigating the error, I see that the battery...
View ArticleRe: PE2950 G3 problem with Perc 6i battery after firmware upgrade
Hello SteveThe battery may actually be working with both firmware revisions. If the battery falls below a certain absolute state of charge it will report failed. The older firmware may not have been...
View ArticleServer 2012 - Enable RemoteFX on Precision T7500
All,I figured I'd start here given my goal is to turn a T7500 into a remoteapp server running 2012 with RemoteFX enabled, and when it comes to servers, this is the place to go.Here's my issue; before I...
View ArticleRe: Server 2012 - Enable RemoteFX on Precision T7500
From my T7500 running dual E5603's:Coreinfo v3.2 - Dump information on system CPU and memory topologyCopyright (C) 2008-2012 Mark RussinovichSysinternals - www.sysinternals.comIntel(R) Xeon(R) CPU...
View ArticleRe: Server 2012 - Enable RemoteFX on Precision T7500
Thank you for the quick resopnse! Do you happen to have the option to enable EPT in your bios, and have you / can you actually enable it? Thanks!!!
View ArticleDell Poweredge 1600sc not posting after start menu shutdown
I have a Dell poweredge 1600sc that was give to me not working. After buying a motherboard and 4gb of memory and installing a 80 gig Hd, i got it to work. I installed windows server 2003 first then...
View ArticleClik here to view.
Re: Dell Poweredge 1600sc not posting after start menu shutdown
Hello skilld420It sounds like the power button is unresponsive. The power button is part of the Front Control Panel assembly. I would suggest reseating the cable for the front panel. Make sure the...
View ArticleRe: PE2950 G3 problem with Perc 6i battery after firmware upgrade
Hi, you are right, the battery was failed. It's possible to run the Perc controller without battery ? If yes, it's possible to remove the battery warning when I remove it when the server boot ?
View Article