Re: Installing old pc image of Win 2003 to Poweredge 2600 using Acronis 2012
See my post earlier in the thread: 4 Jul 2013 6:01 AM
View ArticleRe: Installing old pc image of Win 2003 to Poweredge 2600 using Acronis 2012
wrt the RAMDisk error. How much memory is in the system and what is/are the min. required by Acronis ?
View ArticleAdditional RAM / 2nd processor upgrade for PowerEdge T610
I have a PowerEdge T610 currently with a single processor - an Intel Xeon E5603 1.6GHz, 4.8 GT/s, 4MB cache.I would like to upgrade the memory in this server, but it is currently configured with 6x4GB...
View ArticleRe: Additional RAM / 2nd processor upgrade for PowerEdge T610
1. You cannot mix and match processors. They must be the same. If you do not see one on our site, contact sales. Not all our parts are available online.2. If you order the processor, make sure the...
View ArticleRe: Problem
What is your operating system on this server? It is possible that the Broadcom software needs to be reinstalled. Regards,
View ArticleRe: Additional RAM / 2nd processor upgrade for PowerEdge T610
Thanks Geoff,So, just to confirm, each channel could have, say, 1x 4Gb RDIMM and 1x 8Gb RDIMM, giving a total of 36Gb?Or I could go with 1x 4GB plus 1x 16Gb per channel giving a total of 60Gb?The...
View ArticleHyper-V SR-IOV 11G gen1 R610?
If I have an SR-IOV compatable pci-e Intel quad card can I run SR-IOV even though I do not have an 11G Generation II system?I have read the below kb from Dell but I am not clear if this just refers to...
View ArticleRe: Additional RAM / 2nd processor upgrade for PowerEdge T610
This link may help answer some of your questions: http://www.dell.com/downloads/emea/products/pedge/en/installing_upgrading_ddr3_memory_11g.pdfYou must use the same size and rank in the same channel....
View ArticleRe: Hyper-V SR-IOV 11G gen1 R610?
BIOS version 2.2.10 added support for SR-IOV. Does it let you turn it on? If you do not have the requirements that you listed it isn’t supported, but it may still work we just have not validated other...
View ArticleRe: Hyper-V SR-IOV 11G gen1 R610?
Thanks for the quick reply!I have R610 Bios version 6.3.0. There is no option in the bios for SR-IOV Global Enable.My question, really, is the hardware requirement related just to the onboard nics or...
View ArticleRe: Hyper-V SR-IOV 11G gen1 R610?
According to the Intel documentation it needs to be enabled in the BIOS for PCIe cards as well. The screenshots they are using are from an R620....
View ArticleRe: Hyper-V SR-IOV 11G gen1 R610?
I have seen this Intel doc as well but it si still not clear because it is dealing with an Intel onboard nic on Intel chipset.Notice in both scenarios that the setting is found under integrated devices.
View ArticleRe: Hyper-V SR-IOV 11G gen1 R610?
The previously linked Intel document was talking about pcie cards, not onboard ones, page 7 shows the list of adapters.
View ArticleRe: occasional fatal PCI error with an Intel x520 10gb NIC installed in a...
To update NIC firmware or server bios and things like that, download the Dell Repository manager (current version is 1.6), and this allows you to build a bootable ISO that will update all NIC, PERC,...
View ArticleRe: Additional RAM / 2nd processor upgrade for PowerEdge T610
Thanks again - but I'm slightly confused, as the document appears to state something a bit different.It says that mixed ranks and mixed capacity are both supported. Under mixed capacity, it says:"All...
View ArticleRe: Additional RAM / 2nd processor upgrade for PowerEdge T610
Your suggested setup should work. The quad ranked 16gb RDIMM's have to go in slots A1, A2, A3. As long as you populated the rest exactly, and set the F2 bios to Optimized mode for memory, it should...
View ArticleClik here to view.
OME Update Catalog Broadcom Network Firmware 7.6.15 Fails to install
I just updated my OME catalog, and a new Broadcom network firmware version 7.6.15 has become available.When I attempt to update the firmware on any of my servers either using OME to deploy the update,...
View ArticleRe: OME Update Catalog Broadcom Network Firmware 7.6.15 Fails to install
That is not typical behavior for this update. Did you update the driver as well? Can you reboot and go to the lifecycle controller and attempt the update from there?
View Article