Re: Memory Upgrade to 8gb Dell R200
Hello coronaThe R200 does not support registered/buffered/RDIMMs. You will need to use unregistered/unbuffered/UDIMMs in this server. That is the first thing that pops out at me as making this memory...
View ArticleRe: PowerEdge 840 will not boot or POST.
That power supply model is the one that shipped originally with this server, so there should not be any issue with it working properly. We can try resetting the nvram on the motherboard and see if that...
View ArticleRe: PowerEdge 840 will not boot or POST.
I reset the nvram, no change. according to the manual, there should still be a light code for CPU problems. Does that rule out the CPU?
View ArticleRe: PowerEdge 840 will not boot or POST.
That’s right that there should be a status for a CPU problem, and it doesn’t seem like one, however if all of the other parts have been replaced with the exact same outcome it is unlikely that it is...
View ArticleDell Power Edge T110 II And Crucial Memory Upgrade
I'm after purchasing a RAM upgrade from Crucial for my server. My server's DELL Power Edge T110 II (I ordered it 2 months ago) and here's the exact RAM spec (purchased using the main page wizard on...
View ArticleRe: PowerEdge 840 will not boot or POST.
We replaced the CPU with a Pentium 4, no change. We have only the one PowerEdge 840.
View ArticleRe: Dell Power Edge T110 II And Crucial Memory Upgrade
Hi Dmitry1975,Which slots are you putting the DIMMS in? It should be in the two white slots, slots 1 and 3. For the error codes you are receiving, lights 1 and 3 indicates an invalid or incompatible...
View ArticleRe: PowerEdge 840 will not boot or POST.
That rules out the processor as the issue. It sounds like it powers on, so it probably is not the system control panel, or it would not turn on at all. Does your test bench have a UPS or is it straight...
View ArticleRe: PowerEdge 840 will not boot or POST.
Our entire power system goes through a large UPS. all the other computers are running fine.
View ArticleRe: PowerEdge 840 will not boot or POST.
Interesting thing, i just plugged in a network cable, the NIC lights light up like normal.
View ArticleRe: R720 eSata card - any recommendations on chipset?
Hi,I have a R620 with SAS 6e HBA. Trying to connect a Lacie 4TB external eSATA drive through a mini-SAS to eSATA fanout cable. However, the drive is not detected. I'm desparately seeking expert advice....
View ArticleRe: R720 eSata card - any recommendations on chipset?
I couldn't get it working with a newer SAS 6E card in my 720. Found a good price on a SAS 5/E, put it in a PCI slot and it worked just fine. Bottom line is that I believe you need a card that doesn't...
View ArticleRe: Dell Power Edge T110 II And Crucial Memory Upgrade
Thanks Josh, after installing the memory into 1 & 3 - I'm getting 1 and 2 light solid green and red curve right between them flashing. Then I'm getting no numbers just a flashing red curve (the...
View ArticleRe: R720 eSata card - any recommendations on chipset?
I believe this SAS6E is not a RAID card. The drive should be a single enclosure drive. www.amazon.com/.../ref=sr_1_1I do see the SAS HBA in openmanage and the 2 connectors under it. They do show...
View ArticleRe: R720 eSata card - any recommendations on chipset?
Here's the cable I'm using .www.amazon.com/.../ref=sr_1_1
View ArticleRe: R720 eSata card - any recommendations on chipset?
Ahh, it might not be neither the card nor the cable! (I used this cable - www.amazon.com/.../ref=as_li_ss_tl)It might be the BIOS - just realized that is a 4TB drive - not sure if the geometry for...
View ArticleRe: Insert Asset Tag via command line
Thx very much Chris.I'll give this a go and let u knowJB
View ArticleClik here to view.
Re: Poweredge T310 Motherboard problem
Hello there, i have been searching everywhere for this... i would be very thankful if could you send me the pic...
View ArticleRe: Insert Asset Tag via command line
Hi Chris,When I run it, it goes in to a screen asking to Insert a Floppy Disk (see below).How can I get around that?ThxJohnDiskette 1 - Put a formatted, blank diskette into drive A: and press...
View ArticleRe: Insert Asset Tag via command line
I did the same but used a USB plugin, first formatted with a system and Asset copied to C:/
View Article