Re: R710 and R610 memory upgrade and speed
That is correct, with single or dual rank dimms, using all 3 dimms in the channel results in 800mhz.With you wanting to use 8 dimms, you will need to populate as follows to get the 1333.A1, A2, A4, A5...
View ArticleRe: R710 and R610 memory upgrade and speed
GREAT! Thank you Chris for the great support.
View ArticleRe: T320 PSU upgrade after the fact?
Did this get resolved? i ask because I just saw a message that says to turn off Turbo mode, and that should resolve the issue.
View ArticleRe: Dell PE R720 - Slow POST time
Hi guys,I am having R720. It takes 15-20 minutes since I reboot from rhel 5.9 to get the ssh working. I am actually remote , so don't have console access. I am not sure if it's RHEL's init or POST...
View ArticleRe: T320 PSU upgrade after the fact?
That did indeed fix the problem. I meant to post my solution but got side tracked and didn't get a chance. Going into System Profiles, setting it to custom and turning off Turbo has cleared the...
View Article1500SC ps fan - thermo controlled or always-on?
I have a 1500SC that I use as a toy webserver for sw development. I just noticed that the ps fan isn't running, but can't seem to discover anything in the docs about whether that's normal. If it's...
View ArticleRe: 1500SC ps fan - thermo controlled or always-on?
MMAcD,Is there an amber light on the back of the power supply?
View ArticleT310 - Upgrade motherboard.
HelloGot a spare T310 sitting here not really doing anything. The spec is soo good its a shame to let it rot away.Love to make use of it as a desktop PC but I note the motherboard will not really...
View ArticleRe: T310 - Upgrade motherboard.
To a non-Dell board that would let you add a graphics card?It depends on a few things. Which processor do you have? Assuming a Xeon 34xx, that severely limits your options. For example, on...
View ArticleRe: R620 with extra 5719QP card only 2 ports work on it.
BTW, I have now also tried XenServer 6.0.2 and the 5719 ports don't work there either.
View ArticleMix Single and Dual Rank DIMM's
HiI upgraded RAM from 12GB (6x2GB single rank) to 64GB (8x8GB dual rank) on a R710. I putted the new dual rank DIMM's in on optimizer mode as per the user manual.I'm wondering if I can use the single...
View ArticleRe: Mix Single and Dual Rank DIMM's
FamousRuler,The R710 does support mixing single, dual, or quad ranked dimms. The only rule with order is when using quad ranked they must be in the white slots. With single and dual there is no...
View ArticleRe: Remote Access Configuration Utility prompt stops server from starting
I had a PowerEdge R300 doing the same thing. I only had one hard drive in there, but the second SATA port was enabled. After I disabled the second SATA port everything worked fine.
View ArticleClik here to view.
VMWARE PSOD, PURPLE SCREEN OF DEATH! dell 2950 III
Tried to use my server today, had the purple screen of death!Restarted the server, after 5 hours, same issue.I DO have dell support, but it is very hard to get support.service tag 6LHB13JBy checking...
View ArticleRe: VMWARE PSOD, PURPLE SCREEN OF DEATH! dell 2950 III
Just as a test, try disabling the onboard Sata controller in the BIOS. Is this 3.5? if so, which version? And what version of BIOS do you have?
View Article"Attempting PXE boot" - make it stop!
Everytime I reboot, the system shows "Attempting PXE boot" in upper right of screen after the progress bar fully loads. Any ideas?Specs: PowerEdge R610one add in Quad port Intel ET NICBios Version...
View ArticleRe: VMWARE PSOD, PURPLE SCREEN OF DEATH! dell 2950 III
BIOS is the latest 2.7 and SATA controller is already disabled on the BIOS.i finally made contact with dell support and they told me is the chipset issue, they will replace the mainboard by tuesday!
View ArticleRe: VMWARE PSOD, PURPLE SCREEN OF DEATH! dell 2950 III
A chipset issue? did they give you a case number?
View ArticleRe: "Attempting PXE boot" - make it stop!
Boot to the BIOS Setup, Integrated Devices, and set NIC's to Enabled or Enabled without PXE rather than Enabled with PXE ... or something similar. Or you can try to disable NIC's in the Boot Sequence...
View Article