Re: PE2650, No Post.
I recently reseated the processor, so It should be correctly seated.. I will have to check again though.As for the processor being damaged I'm unsure I'll have to do a swap. Its also a dual...
View ArticleRe: RAM upgrade for T610
Hello,The T610 supports 12 DIMMS up to 192GB of RAM with Registered ECC memory. It also supports a max memory of 24GB with Unbuffered ECC memory.You can refer the following link for the memory....
View ArticlePE2950 Gen 1
I have a PERC 5 in my machine w/ (6) SAS/SATA slots, Is the raid controller upgradeable to say a PERC 6?
View ArticleRe: PE2950 Gen 1
Yes, but you will need to make sure your system firmware (BIOS, ESM, etc.) is up to date.What are you hoping to gain with a PERC 6 over a PERC 5?
View ArticleClik here to view.
hard drive, backplane or both?
Hi All, I got a Dell PE 6850 with Win 2000 SP4. Few days ago the hard drive on the server failed & we got it replaced but the disk rebuild process failed. Logged on to array manager (see below)...
View ArticleRe: hard drive, backplane or both?
If you expand Backplane (Channel 0), you will see the disk that has actually failed ... the red X on Backplane does not mean it is bad - it simply lets you bullet down to the bad device, so the red X...
View ArticleRe: hard drive, backplane or both?
Thanks Flash, details below******** System configuration file generated by Array Manager *********Release information**Version = 3.5.0Build = 575.6Install Directory = D:\Program Files\Dell\SysMgt\Array...
View ArticleRe: PowerEdge Compatible GPU List
I have successfully run the K10s in Linux on the R720s. There is a PCI error message that you can skip and you need to modify the BIOS so that the fan speeds run at max. We get good performance out of...
View ArticleChoosing Memory for PowerEdge 6850
Hi,I recently purchased a PE 6850... I'm shopping for parts for it...I am (and have been since the 1990's) confused when it comes to choosing memory.The specs for the 6850 call for "144-bit ECC...
View ArticlePoweredge 1750 I/O question
http://www.dell.com/downloads/global/products/pedge/en/1750_specs.pdfIf someone can take a look at this spec sheet for the 1750 rack server and clarifiy exactly how the PCI (I/O) slots are set up I...
View ArticleRe: Choosing Memory for PowerEdge 6850
The Dell documentation is the best starting point. Both the manual and the spec sheet lists PC2-3200 (same as DDR2 400MHz), Registered ECC ... that is what you should be looking for.Memory will...
View ArticleRe: Choosing Memory for PowerEdge 6850
Thanks! I decided to stick with standard Dell ram...
View ArticleRe: Choosing Memory for PowerEdge 6850
You don't necessarily need to get Dell-branded RAM, but you should shop for RAM with specs as close to the listed specs as possible.
View ArticleClik here to view.
Dell R610 boot from iSCSI
Hello!I try to install XenServer 6.1 in to iSCSI LUN, I successfully configured Broadcom BCM5709C Network Adapter to boot from iSCSI, but when I start to install XenServer an error occurs, that...
View ArticleDRAC card
Appologies if this is in the wrong section, was a bit unsure of where to post it.I have a R900 running Windows 2008 64, I have installed and configured a DRAC card, I can access the card remotely but...
View ArticleRe: DRAC card
Peter, I checked the same in our LAB and it is working fine. Can you provide below information as it help me in reproducing the issue?1: What is the DRAC5 FW version?2: Which Client Operating...
View ArticleRe: r200 bios problem
in restored IronPort BIOS, box RAID set in "off" and new write DELL BIOS 1.4.3 two beep returned .
View ArticleE1618 Predictive Failure on both PSUs, how to troubleshoot
Hi,I have a PowerEdge R300server and the following warnings:PS 1 Status: Power Supply sensor for PS 1, predictive failure was assertedPS 2 Status: Power Supply sensor for PS 2, predictive failure was...
View ArticleRe: Dell R610 boot from iSCSI
It sounds like your linux and Xenserver do not have the correct drivers to detect the iSCSI LUN. You can try the Red Hat downloads on the Dell site, but you may need to call your OS support group to...
View Article